Glow Plug Control Circuit
The PACCAR-P0380 (PACCAR MX) diesel fault code means: Glow Plug Control Circuit. This is a minor severity code.
- Keep driving?
- Short distances only
- DIY difficulty
- intermediate
- Estimated cost
- $300-$3,500
Down with a PACCAR fault on the road?
Get connected with a verified mobile diesel mechanic near you. Verified diesel & reefer techs, launching on the freight corridor.
Find a mobile mechanic →A $30 car code reader can't do diesel. The HD7000 reads full-system codes and does parked DPF regen, idle/speed-limit, and service resets from the cab — on everything from a 6.7 Cummins/Power Stroke/Duramax pickup to Class-8 trucks (Detroit, Paccar, CAT, Volvo, Mack, International).
Full-system 6/9/16-pin diesel scan tool for Cummins, Paccar, CAT, Detroit and more — plug-and-play, no subscription. A cheaper way to read heavy-duty codes a basic OBD2 scanner skips entirely.
Affiliate links — we earn a commission at no extra cost to you.
Common Symptoms
- Check Engine Light illuminated
- Performance loss or engine derate
- Rough idle, hard starting, or stalling
- Scan tool communication issues (U-codes)
- Possible smoke or unusual noise
Probable Causes (Ranked by Likelihood)
- Sensor or actuator failure in the affected circuit Likely
- Wiring harness damage, chafing, or corrosion Likely
- Contaminated fuel / DEF / coolant Possible
- ECM or CEM needs reflash for known calibration issue Possible
- Mechanical wear (high-mileage truck) Possible
Frequently Asked Questions
What does PACCAR MX code P0380 mean?
PACCAR MX code P0380 (Glow Plug Control Circuit) is a minor-severity diagnostic trouble code set by the engine or aftertreatment control module on MX-11 and MX-13 engines in Kenworth and Peterbilt trucks. It indicates a fault in the engine system that should be diagnosed with DAVIE4 or PACCAR ESA.
Can I drive a Kenworth or Peterbilt with PACCAR P0380?
Possibly — short distances may be OK, but ignoring the fault risks progressive damage, regen failure, or derate. Address promptly.
How much does it cost to fix PACCAR MX P0380?
Typical repair runs $300-$3,500. Sensor or wiring repairs are at the low end; injector, DEF pump, DPF, or EGR cooler jobs are at the high end. Dealer-level DAVIE4 software is often required for programming or calibration after parts replacement.
Mechanics Guide Step-by-step diagnosis
Step-by-Step Diagnostic Procedure
Pull all active and inactive codes from ECM, CEM, ABS, and TCM with DAVIE4 — root cause often sets multiple codes.
Capture freeze frame data and compare values to known good operating ranges.
Back-probe the affected sensor / actuator circuit with a DMM key-on engine-off and running.
Inspect wiring harness at valve cover, turbo, and frame crossover points for chafing / rub-through.
After repair, clear codes and perform a road-test drive cycle to verify fault does not return.
Sources 2
This page is built from documented references. Verify against your own service info before repair work.
- SAE J1939-73Application Layer: Diagnostics (defines the SPN/FMI fault-identifier framework)
- SAE J2012Diagnostic Trouble Code Definitions (defines P0380 as a generic OBD-II code)
P0380 on Other Platforms
The same code ID appears across other engines, vehicles, and equipment. Diagnostic flow varies by platform — see the matching breakdown:
Commonly Affected Vehicles
- Kenworth T680 with PACCAR MX-13
- Kenworth T880 with PACCAR MX-13
- Kenworth W990 with PACCAR MX-13
- Peterbilt 579 with PACCAR MX-13
- Peterbilt 389 with PACCAR MX-13
- Peterbilt 567 with PACCAR MX-13
- Kenworth T440 with PACCAR MX-11
- Kenworth T470 with PACCAR MX-11
- Peterbilt 520 with PACCAR MX-11
Explore More
Was this helpful?
Send this to whoever is fixing the truck — your tech, or the person asking what the fault means.