Invalid Data Received from ECM
The HINO-U0401 (Hino) diesel fault code means: Invalid Data Received from ECM. This is a moderate severity code.
- Keep driving?
- Short distances only
- DIY difficulty
- intermediate
- Estimated cost
- $250-$2,800
Down with a Hino fault on the road?
Get connected with a verified mobile diesel mechanic near you. Verified diesel & reefer techs, launching on the freight corridor.
Find a mobile mechanic →A $30 car code reader can't do diesel. The HD7000 reads full-system codes and does parked DPF regen, idle/speed-limit, and service resets from the cab — on everything from a 6.7 Cummins/Power Stroke/Duramax pickup to Class-8 trucks (Detroit, Paccar, CAT, Volvo, Mack, International).
Full-system 6/9/16-pin diesel scan tool for Cummins, Paccar, CAT, Detroit and more — plug-and-play, no subscription. A cheaper way to read heavy-duty codes a basic OBD2 scanner skips entirely.
Affiliate links — we earn a commission at no extra cost to you.
Common Symptoms
- CEL with multiple codes set together
- No-start (CKP/CMP)
- Gauge/speedometer dropout
- Transmission limp or shift faults
- Scan tool communication loss
Probable Causes (Ranked by Likelihood)
- Damaged sensor or wiring in affected circuit Likely
- CAN bus harness chafing in chassis routing Possible
- Poor battery or ground — dual-battery J08 setups common Possible
- Water intrusion at cab / body harness disconnect Possible
- ECM / TCM internal fault (rare) Less Likely
Frequently Asked Questions
What does Hino code U0401 mean?
Hino diagnostic trouble code U0401 (Invalid Data Received from ECM) is a moderate-severity fault on Hino medium-duty diesel engines. It indicates a problem in the communication that should be verified with a scan tool (Hino DX3 / DX4) before replacing any parts.
Can I drive my Hino truck with U0401?
Short runs may be possible but do not ignore — Hino medium-duty aftertreatment faults cascade quickly into 5-mph derate or no-restart. Schedule diagnosis immediately.
How much does it cost to fix Hino U0401?
Estimated repair cost runs $250-$2,800. Sensor, wiring, and DEF-related repairs fall at the low end; DPF service, turbo, injector, and EGR cooler work fall at the high end and may require dealer-level programming.
Mechanics Guide Step-by-step diagnosis
Step-by-Step Diagnostic Procedure
Inspect engine-to-frame and engine-to-body grounds for corrosion — the #1 root cause of U-codes on Hino medium-duty.
Measure battery voltage at rest and cranking. Replace weak batteries before diagnosing CAN faults.
Measure CAN H / CAN L resistance at diagnostic port — ~60 ohms key off indicates healthy dual-termination.
For CKP / CMP, ohm the sensor, inspect reluctor for damage, verify air gap with feeler gauge.
Run ECM / TCM self-diagnostic routine on Hino DX3 if wiring and power check out.
Sources 1
This page is built from documented references. Verify against your own service info before repair work.
- SAE J1939-73Application Layer: Diagnostics (defines the SPN/FMI fault-identifier framework)
U0401 on Other Platforms
The same code ID appears across other engines, vehicles, and equipment. Diagnostic flow varies by platform — see the matching breakdown:
Commonly Affected Vehicles
- Hino 155 / 155h with J05 5.1L
- Hino 195 / 195h (hybrid) with J05D 5.1L
- Hino 258 / 258LP / 268 with J08 7.7L
- Hino 338 / 338CT with J08 7.7L
- Hino 358 / 358CT (post-2019 J-series / A09C)
- Toyota Dyna / Hino-branded export chassis with J05/J08
Explore More
Was this helpful?
Send this to whoever is fixing the truck — your tech, or the person asking what the fault means.