CAT-SPN412-FMI1 moderate Caterpillar ›

EGR Temperature Below Normal

The CAT-SPN412-FMI1 (Caterpillar) diesel fault code means: EGR Temperature Below Normal. This is a moderate severity code.

My Garage →
Keep driving?
Short distances only
DIY difficulty
intermediate
Estimated cost
$200-$1500
Mobile mechanic network · I-5 corridor pilot

Down with a CAT fault on the road?

Get connected with a verified mobile diesel mechanic near you. Verified diesel & reefer techs, launching on the freight corridor.

Find a mobile mechanic →
Built for Diesel — Not a Car Reader
ANCEL HD7000 Heavy-Duty Diesel Scanner

A $30 car code reader can't do diesel. The HD7000 reads full-system codes and does parked DPF regen, idle/speed-limit, and service resets from the cab — on everything from a 6.7 Cummins/Power Stroke/Duramax pickup to Class-8 trucks (Detroit, Paccar, CAT, Volvo, Mack, International).

Check Price on Amazon
FOXWELL HD301 Diesel Truck Scanner
Lower-Cost Diesel Option
FOXWELL HD301 Diesel Truck Scanner

Full-system 6/9/16-pin diesel scan tool for Cummins, Paccar, CAT, Detroit and more — plug-and-play, no subscription. A cheaper way to read heavy-duty codes a basic OBD2 scanner skips entirely.

Check Price on Amazon

Affiliate links — we earn a commission at no extra cost to you.

Common Symptoms

  • Check Engine Light or warning lamp
  • Engine protect / derate / shutdown possible
  • System performance affected

Probable Causes (Ranked by Likelihood)

  • Sensor / actuator internal failure Likely
  • Wiring or connector issue in the affected circuit Likely
  • Related system mechanical issue Possible
  • ECM calibration or software issue Less Likely

Frequently Asked Questions

What does CAT SPN412-FMI1 mean?

CAT SPN412-FMI1 (EGR Temperature Below Normal) is a moderate-severity fault reported over the J1939 data link. EGR gas temp sensor reading low / EGR not flowing. CAT ECMs report many of the same faults both as CID/FMI (proprietary) and SPN/FMI (J1939) — either form points to the same physical issue.

Can I drive with CAT SPN412-FMI1?

Short distances may be acceptable, but plan the repair promptly. Ignoring the fault risks progressive damage or derate.

How much does CAT SPN412-FMI1 cost to fix?

Typical repair is $200-$1500. Simple sensor/wiring repairs fall at the low end; component, actuator, or aftertreatment work falls at the high end and usually requires CAT ET for programming.

Mechanics Guide Step-by-step diagnosis

Step-by-Step Diagnostic Procedure

  1. Connect CAT ET and confirm the SPN/FMI is active; record live data for the affected parameter.

  2. Inspect wiring and connectors for the affected circuit; back-probe and check with a DMM.

  3. Perform component test on the sensor / actuator per CAT service manual.

  4. Repair wiring, replace component, or reflash ECM as CAT ET diagnostics direct.

Sources 1

This page is built from documented references. Verify against your own service info before repair work.

  • SAE J1939-73Application Layer: Diagnostics (defines the SPN/FMI fault-identifier framework)

Commonly Affected Vehicles

  • Kenworth T800 with CAT C15
  • Kenworth W900 with CAT C15
  • Kenworth T2000 with CAT C15
  • Peterbilt 379 with CAT C15
  • Peterbilt 389 with CAT C15
  • Peterbilt 386 with CAT C15
  • Peterbilt 387 with CAT C15
  • Freightliner Classic XL with CAT C15
  • International 9200i with CAT C15
  • International 9400i with CAT C15
  • Western Star 4900 with CAT C15
  • Western Star 5900 with CAT C15
  • Kenworth T800 with CAT C13
  • Kenworth T660 with CAT C13
  • Peterbilt 386 with CAT C13
  • Peterbilt 387 with CAT C13
  • Freightliner Columbia with CAT C13
  • International 9200i with CAT C13

Explore More

More Caterpillar codes → Diesel home All diesel codes Heavy-duty Guides

Was this helpful?

Send this to whoever is fixing the truck — your tech, or the person asking what the fault means.