Fuel Rail Pressure Sensor - Voltage Low
The CAT-CID1797-FMI4 (Caterpillar) diesel fault code means: Fuel Rail Pressure Sensor - Voltage Low. This is a serious severity code.
- Keep driving?
- Short distances only
- DIY difficulty
- advanced
- Estimated cost
- $300-$4500
Down with a CAT fault on the road?
Get connected with a verified mobile diesel mechanic near you. Verified diesel & reefer techs, launching on the freight corridor.
Find a mobile mechanic →A $30 car code reader can't do diesel. The HD7000 reads full-system codes and does parked DPF regen, idle/speed-limit, and service resets from the cab — on everything from a 6.7 Cummins/Power Stroke/Duramax pickup to Class-8 trucks (Detroit, Paccar, CAT, Volvo, Mack, International).
Full-system 6/9/16-pin diesel scan tool for Cummins, Paccar, CAT, Detroit and more — plug-and-play, no subscription. A cheaper way to read heavy-duty codes a basic OBD2 scanner skips entirely.
Affiliate links — we earn a commission at no extra cost to you.
Common Symptoms
- Hard start or extended crank
- Low power, derate
- Black or white smoke
- Check Engine Light
- Stall at idle
Probable Causes (Ranked by Likelihood)
- Fuel filter restriction / old filters Very Likely
- HP fuel pump internal wear Likely
- Fuel rail regulator stuck Likely
- Injector internal leak dropping rail pressure Possible
- Air intrusion through supply plumbing or filter housing Possible
Frequently Asked Questions
What does CAT CID1797-FMI4 mean?
CAT code CID1797-FMI4 (Fuel Rail Pressure Sensor - Voltage Low) is a serious-severity fuel system fault. Fuel rail pressure sensor shorted to ground. Common-rail C15/C13 engines rely on 30,000 psi+ rail pressure; even small supply issues or injector leaks can flag this.
Should I replace the HP pump right away?
No — start with fuel filters and a supply pressure test. HP pump replacement on a C15 is expensive ($3,000+) and often unnecessary. Confirm injector return flow and supply pressure first.
How much to fix CAT CID1797-FMI4?
Filter service is $80-$150. Supply pump replacement is $400-$900. Injector replacement runs $500-$800 each installed. HP pump replacement is $3000-$4500.
Mechanics Guide Step-by-step diagnosis
Step-by-Step Diagnostic Procedure
Confirm fault in CAT ET and record commanded vs actual rail pressure at idle and rated.
Change fuel filters and prime system; retest.
Check supply pump outlet pressure with a gauge; must meet HP pump inlet spec.
Test for air intrusion in low-pressure side (clear line).
Perform injector return flow test to identify leaking injector(s).
If supply and injectors test OK, HP pump wear is the likely cause.
Sources 1
This page is built from documented references. Verify against your own service info before repair work.
- SAE J1939-73Application Layer: Diagnostics (defines the SPN/FMI fault-identifier framework)
Commonly Affected Vehicles
- Kenworth T800 with CAT C15
- Kenworth W900 with CAT C15
- Kenworth T2000 with CAT C15
- Peterbilt 379 with CAT C15
- Peterbilt 389 with CAT C15
- Peterbilt 386 with CAT C15
- Peterbilt 387 with CAT C15
- Freightliner Classic XL with CAT C15
- International 9200i with CAT C15
- International 9400i with CAT C15
- Western Star 4900 with CAT C15
- Western Star 5900 with CAT C15
- Kenworth T800 with CAT C13
- Kenworth T660 with CAT C13
- Peterbilt 386 with CAT C13
- Peterbilt 387 with CAT C13
- Freightliner Columbia with CAT C13
- International 9200i with CAT C13
Related Codes
Explore More
Was this helpful?
Send this to whoever is fixing the truck — your tech, or the person asking what the fault means.