Injection Actuation Pressure Sensor - Voltage Low
The CAT-CID164-FMI4 (Caterpillar) diesel fault code means: Injection Actuation Pressure Sensor - Voltage Low. This is a serious severity code.
- Keep driving?
- Short distances only
- DIY difficulty
- advanced
- Estimated cost
- $400-$3500
Down with a CAT fault on the road?
Get connected with a verified mobile diesel mechanic near you. Verified diesel & reefer techs, launching on the freight corridor.
Find a mobile mechanic →A $30 car code reader can't do diesel. The HD7000 reads full-system codes and does parked DPF regen, idle/speed-limit, and service resets from the cab — on everything from a 6.7 Cummins/Power Stroke/Duramax pickup to Class-8 trucks (Detroit, Paccar, CAT, Volvo, Mack, International).
Full-system 6/9/16-pin diesel scan tool for Cummins, Paccar, CAT, Detroit and more — plug-and-play, no subscription. A cheaper way to read heavy-duty codes a basic OBD2 scanner skips entirely.
Affiliate links — we earn a commission at no extra cost to you.
Common Symptoms
- Check Engine Light
- HEUI pressure reads pegged high on CAT ET
- Engine may not start or runs very poorly
Probable Causes (Ranked by Likelihood)
- Signal wire shorted to ground Very Likely
- Sensor or solenoid shorted internally Likely
Frequently Asked Questions
What does CAT code CID164-FMI4 mean?
CAT code CID164-FMI4 (Injection Actuation Pressure Sensor - Voltage Low) is a serious-severity fault in the HEUI injection system. HEUI injection actuation pressure sensor voltage reads below normal, typically short to ground. HEUI (Hydraulically actuated Electronically controlled Unit Injectors) uses high-pressure engine oil to fire injectors, so HEUI faults often trace to oil pump wear, oil leaks, or sensor failures.
Can I drive with CAT CID164-FMI4?
Short distances may be possible, but plan repair soon — HEUI faults tend to progress quickly.
How much does it cost to fix CAT CID164-FMI4?
Typical cost is $400-$3500. Sensor or IAPR replacement is at the low end; high-pressure oil pump or injector work is at the high end and usually requires CAT dealer-level diagnostic time.
Mechanics Guide Step-by-step diagnosis
Step-by-Step Diagnostic Procedure
Connect CAT ET and confirm the active fault; note HEUI actuation pressure live value.
Inspect IAPR connector and wiring at front of engine for damage.
Measure HEUI actuation pressure with CAT ET during cranking; spec ~870 psi at cranking for start.
If pressure is low at cranking, test HP oil pump and check injector cup seals for oil loss.
Replace sensor, IAPR, or pump as indicated by tests.
Sources 1
This page is built from documented references. Verify against your own service info before repair work.
- SAE J1939-73Application Layer: Diagnostics (defines the SPN/FMI fault-identifier framework)
Commonly Affected Vehicles
- Kenworth T800 with CAT C15
- Kenworth W900 with CAT C15
- Kenworth T2000 with CAT C15
- Peterbilt 379 with CAT C15
- Peterbilt 389 with CAT C15
- Peterbilt 386 with CAT C15
- Peterbilt 387 with CAT C15
- Freightliner Classic XL with CAT C15
- International 9200i with CAT C15
- International 9400i with CAT C15
- Western Star 4900 with CAT C15
- Western Star 5900 with CAT C15
- Kenworth T800 with CAT C13
- Kenworth T660 with CAT C13
- Peterbilt 386 with CAT C13
- Peterbilt 387 with CAT C13
- Freightliner Columbia with CAT C13
- International 9200i with CAT C13
- Kenworth T370 with CAT C7
- Kenworth T470 with CAT C9
- Peterbilt 335 with CAT C7
- Peterbilt 340 with CAT C9
- Freightliner M2 106 with CAT C7
- International 4300 with CAT C7
- Thomas / Bluebird school bus with CAT C7
- IC Bus shuttle with CAT C7
Related Codes
Explore More
Was this helpful?
Send this to whoever is fixing the truck — your tech, or the person asking what the fault means.